Search results for "Polymer Electrolyte Membrane"
showing 8 items of 8 documents
A stacked interleaved DC-DC buck converter for proton exchange membrane electrolyzer applications: Design and experimental validation
2019
Abstract Since the two last decades, hydrogen production has been attracting the attention of the scientific community thanks to its inherent very low pollution when energy coming from renewable energy sources (RESs) are used. However, it implies the use of DC/DC converters to interface source and load. These conversion systems must meet several requirements from current ripple point of view, energy efficiency, and performance to preserve the sustainability of hydrogen production. This article proposes the design and realization of a stacked interleaved buck converter to supply a proton exchange membrane electrolyzer. The converter is designed to ensure a low output current ripple and a sui…
Design of a LLC Resonant Converter for Powering a PEM Electrolyzer
2021
International audience; This paper proposes the design of a LLC resonant converter to supply a proton exchange membrane (PEM) electrolyzer. The PEM requires a low voltage with high current, a reduced output voltage ripple, and an overdamped dynamic behavior of the converter to avoid voltage overshoots. The designed converter allows satisfying the design constraints, minimizing switching and reverse recovery losses; the efficiency is influenced mainly by the output rectifier's conduction losses.
Hydrogen from The Sea: The Challenge of the Future. Present and Future Developments
2014
In this paper we proposed the use of saline water to product hydrogen. As far as using saline water, can be proposed two different scheme and technology. The aim of this work is to design an electrolyze system capable of utilizing sea water for direct electrolysis. It is probable that these systems would operate at a low power density and electrolyze only a small portion of the water in contact with electrodes. In particular, we present the results obtained by two different prototype of electrolyzer: one with steel electrodes and the second electrodes with titanium. Further experiments were carried out by changing the electrolytic solution of water and sodium chloride in real seawater. Fina…
PEM electrolyzer characterization with carbon-based hardware and material sets
2021
Abstract The research and development of proton exchange membrane water electrolysis (PEMWE) is an upcoming and growing area due to a rising interest in hydrogen as an energy carrier. Operating conditions are harsher than in a fuel cell system, particularly because the potentials required for the oxygen evolution reaction are significantly higher. In commercial water electrolysis systems, this is compensated by typically using titanium material sets that are often protected against oxidation through coating processes. Such material choices make small scale research hardware and porous transport layers expensive and difficult to source. In this work, we show that the stability of traditional…
Evaluation of a new Cr-free alloy as interconnect material for hydrogen production by high temperature water vapour electrolysis: Study in cathode at…
2012
International audience; For economic and ecological reasons, hydrogen is considered as a major energetic vector for the future. Hydrogen production via high temperature water vapour electrolysis (HTE) is a promising technology. A major technical difficulty related to high temperature water vapour electrolysis is the development of interconnects working efficiently for a long period. Working temperature of 800 degrees C enables the use of metallic materials as interconnects. High temperature corrosion behaviour and electrical conductivity of a new Cr-free Fe-Ni-Co alloy were tested in cathode atmosphere (H-2/H2O) at 800 degrees C. The alloy exhibits a poor oxidation resistance but an excelle…
Optimisation of metallic interconnects for hydrogen production by high temperature water vapour electrolysis
2012
For economical and environmental reasons, hydrogen is considered as a major energetic vector for the future. Hydrogen production via high temperature water vapour electrolysis (HTE) is a promising technology. A major technical difficulty related to high temperature water vapour electrolysis is the development of interconnects working efficiently for a long period. Working temperature of 800°C enables the use of metallic materials as interconnects. Chromia forming alloys are among the best candidates. The interconnect material chosen in the present study is a ferritic stainless steel with 18% chromium content. High temperature corrosion resistance and electrical conductivity of the alloy was…
Nanostructured Material Fabrication for Energy Conversion
2011
The electrochemical deposition is a suitable via to fabricate nanostructured materials for energy conversion, and for other purposes. This paper deals with the electrochemical synthesis of nanostructured alloys and ruthenium oxide, which can be used in Li-ion batteries and polymer electrolyte membrane electrolyzers.
Life cycle assessment of solid oxide fuel cells and polymer electrolyte membrane fuel cells: A review
2017
Fuel cells (FCs) are among the key technologies that Europe will have to rely on in order to comply with the most recent environmental targets inspired by decarbonization and circular economy. The assessment of the real advantages of using FCs for producing energy must include a reliable analysis of the energy and environmental impacts during the life cycle of these systems, including the raw materials supply, production, use, and disposal. In this context, the life cycle assessment (LCA) is a well-established methodology for assessing the eco-profile of products and services and for identifying the components and the life cycle steps having the largest contribution to energy and environmen…